Maytag Centennial Washer Stuck on Wash [9 Fixation 2024]

Purchasing products from a well-known brand is one thing but dealing with its issues is another one. You might know this thing that every brand has a range of its own appliances and so does Maytag. As said before, every appliance teases the users to some extent. Maytag Centennial Washer getting stuck on wash is one of the most commonly faced issues. Let us have a brief discussion regarding it, shall we?

Maytag Centennial Washer Stuck on Wash – Potential Reasons

A Maytag Centennial Washer Stuck on Wash might be due to the following reasons.

  • Faulty Timer
  • Defective Lid Switch
  • Malfunctioning Control Board
  • Faulty Water Level Valve
  • Poor Drainage
  • Usage of Wrong Detergent
  • Insufficient Water Supply
  • Clogged Filters
  • Damaged Drive Belt

How to Solve Maytag Centennial Washer being stuck on Wash Issue?

If you truly want to know how to get rid of this error then I suggest you invest your time in the below mentioned troubleshooting steps.

Maytag Centennial Washer Stuck on Wash
Maytag Centennial Washer Stuck on Wash

Also Check: LG Direct Drive Washing Machine Problems

Also Check: Are Portable Washing Machines Allowed in Apartments 


  1. Faulty Timer:

Maytag or any other washer depends on the timer to send signals regarding rinsing and washing. However, if the timer starts showing delays or is Skippy then you can’t rely on it. Having a faulty timer means the washer won’t know what to do exactly.

To get through this problem you can turn the timer manually. But this will get rid of the problem for a short time only. The problem will reappear after some time.

Fix Method:

Buy a new timer of the same model as your washer and replace it with the old one. You can do this by following the below steps.

  • Unplug the washer.
  • Disconnect the Water Supply.
  • Start disassembling the washer’s control panel.
  • Access the timer by unscrewing the control panel.
  • Place the new timer in place of the old one and screw it rightly.

  1. Defective Lid Switch

Do you own a Maytag Centennial top loader washer? If yes, then you must check the lid switch. In top loaders, the switch is responsible for closing the washer lid properly and moving it to the next cycle. The case would be extremely opposite if the switch has gone faulty.

Fix Method

Take a multimeter and test the lid switch. Check whether you witness any continuity or not. If not then you have to get the switch replaced no matter what.


  1. Malfunctioning Control Board

Maytag Centennial Washers are extremely durable especially when it comes to their control boards. If the control board has become faulty then the washer is as good as dead. But you should consider this as your last option.

Fix Method

Before investing into the big replacement, it is encouraged to perform a reset to check whether the machine goes past this cycle or not. If it doesn’t then note the error code that the display is showing. Error code being associated with the control panel is an indication for you to have the control panel replaced as soon as possible.


  1. Faulty Water Level Valve

As clear from its name, a water level valve is responsible for regulating water to your washer. To have it working properly you should open it fully and have it clog-free. This brings us to the conclusion that the water level valve shouldn’t be worn or clogged if you expect it to work properly.

Fix Method

Take a multimeter and use it to test the water level valve. If you see any continuity then it means it is working just fine however, if the case is otherwise then you need to replace it. Make sure to make it clog-free using vinegar.


  1. Poor Drainage

The washer will wait for the water to drain completely before moving on to the next cycle. So make sure there isn’t any water present in the drum during the drainage process. Hose pump or drain pump are two places where clogging might occur and if this happens then the washer will refuse to change its cycle.

Fix Method

Access the drain hose and look for possible clogs and kinks. This will allow maximum drainage to happen. Moreover, have the washer’s drain pump clogged-free to avoid other inconveniences.


  1. Usage of Wrong Detergent

Using a wrong detergent type will cause excess suds which will be detected by Maytag Centennial. This is also one of the reasons behind the problem. The washer might stop mid-cycle and refuse to move to the next cycle due to the usage of too much detergent. Using the wrong detergent type can also cause this issue to occur.

Fix Method

Always use a reasonable amount of detergent when washing the clothes. Use High-Efficiency detergents (HE) which will not form suds quickly. Moreover, these HE detergents are also gentle on your washer.


  1. Insufficient Water

Maytag Centennial washer will move to the next cycle once it is sure that there is enough water to match the load. The water level sensor will show no activity until the tub fills up with sufficient amounts of water. This will not allow the washer to move to the next cycle.

Fix Method

Make sure the water goes to the tub efficiently and with a good pressure. This will help the sensor to detect whenever the washer tub has been filled with water.


  1. Clogged Filters

Presence of clogged filters will slow down the drainage process and if this happens then the washer is most likely to stay in one cycle.

Fix Method

It is encouraged that you replace the washer filters after 6 months depending on their usage. If you are changing the filters yourself then you need to first disconnect the water from the power supply and then detach the old filters from the circuit board.


  1. Damaged Drive Belt

Having a damaged drive belt means that your Maytag Centennial Washer will not move to the next cycle. The belt can break at any moment so to avoid future inconveniences, the washer will stay on the present cycle and won’t move further.

Fix Method

Check the drive belt for damages and if you find any, you need to make the replacement as soon as possible. Don’t wait for the drive belt to break down completely, take the action beforehand.

Maytag Centennial Washer Stuck on Wash
Maytag Centennial Washer Stuck on Wash

Also Check: Reason GE Washer Stuck on Sensing

Frequently Asked Questions

Q – Why is my Washing Machine stuck on the wash cycle?

A – Having a washing machine stuck on the wash cycle might be due to the presence of a faulty timer. A washer doesn’t sense whether the clothes are cleaned or not, it will run each cycle on a pre-set timer.

Q – How to force the Maytag washer to reset?

A – First you need to remove the washer’s plug for about a minute. Re-establish the connection then lift and close the lid 6 times in a 12-second interval. Run a test afterwards to make a confirmation that the washer has been reset successfully.

Concluding Thoughts:

All in all, it is always encouraged to check the components like water-level valve, lid-switch, timer, and control board before making the big investment. If the components have become faulty then the only solution is to replace them with the new ones. Make sure to use the correct detergent type and have all the filters cleaned. This will help you a lot in solving various issues.

Leave a Comment