Whirlpool Duet Dryer Won’t Start Just Beeps [Fixation 2024]

Have you had the experience to buy and use a Whirlpool Duet Dryer? If yes, then you would be familiar with its issue when it refuses to start but only beeps. Beeping is kind of a feedback in some cases like when a cycle has been completed or when there is a reminder for a vital check. Other than these, if the dryer beeps then it means something is definitely wrong.

Whirlpool Duet Dryer Won’t Start Just Beeps

If you also come across this issue then the reasons could be the following:

  • Incorrectly Latched Door
  • Laundry Overload
  • Dirty Lint Screen
  • Overheating
  • Wrong Voltage Supply
  • Defective Start Switch
  • Faulty Back Pulley
  • Defective Control Board

How to Solve Whirlpool Duet Dryer not starting but Beeping Issue?

In order to solve the Whirlpool Duet Dryer Won’t Start Just Beeps issue you need to follow the below mentioned troubleshooting guide. I have briefly explained the potential causes along with their solutions. Make sure to follow the guide properly.

Whirlpool Duet Dryer Won’t Start Just Beeps
Whirlpool Duet Dryer Won’t Start Just Beeps

Also Check: Samsung Dryer Diagnostic Mode [6 Fixations] in 2024

Also Check: Whirlpool Cabrio Dryer Reset [4 Fixations in 2024]

Also Check: LG Dryer d90 No Blockage [6 Fixation in 2024]

Also Check: Maytag Bravos XL Dryer Troubleshooting

Also Check: Whirlpool Duet Dryer Diagnostic Mode

Also Check: How to Reset Samsung Dryer Control Board [Fixation 2024]

Also Check: LG Dryer d80 no Blockage


  1. Incorrectly Latched Door

The dryer door might seem to be closed to us but is it really what the dryer thinks? If the dryer thinks otherwise then it will send a warning through its beep. Another confirmation for this issue is to see the error code, if the display shows OE along with three beeps then it means you need to check the door.

Don’t worry because there is nothing wrong with the door. It’s just that it hasn’t been shut properly. If you have closed the door properly but still hear the beeping then you need to check the door switch.

Fix Method:

Latch the dryer door gently and also check the door switch. Take a multimeter and examine the working of the door switch. If you find no continuity then it means the switch has gone faulty and you need to replace it. After doing this, reset the dryer by unplugging the power cord for exactly half an hour.


  1. Laundry Overload

It is common sense to not overload the dryer with laundry. The drum capacity should stick to ¾, if this limit exceeds then you will start facing other issues like the dryer not spinning or heating. If this is the situation then you will be indicated about the error through a single beep.

Fix Method

Remove all the extra laundry which is causing the drum size to increase. But make sure to not go beyond half as well because it will make it hard for the dryer to run. Moreover, it is not an energy efficient approach.


  1. Dirty Lint Screen

If you are witnessing error code F4E3 then it is a clear indication of restricted airflow. Why does this happen? Well, it happens when the lint filters or screen gets clogged. Even if the dryer starts operating, it will fail to dry the clothes. Remember that the accumulating lint is a huge fire hazard and obviously you wouldn’t want that right?

Fix Method

Check the lint screen and filters carefully. If they are clogged then of course you need to clean them. Take a simple nylon brush, water and detergent to do the filter cleaning.


  1. Overheating

Whirlpool Duet Dryer might get overheated and it will communicate this to you by sending a beeping sound. During this beeping, the dryer won’t be running. There are many issues which contribute to this fact like clogged lint screen, overworking vent or a blocked air vent.

  • Blown up Thermal Fuse

The best use case of thermal fuse is that it protects the dryer from overheating. As soon as the dryer starts overheating, the thermal fuse will blow so the dryer doesn’t have to go through this condition.

  • Blown up Heat Relay

Heat relay is present on the control board which switches ON the blower chamber’s heat when the dryer starts to overheat. If this happens, its fuse will blow up eventually.

Fix Method

Absence of thermal fuse and heat relay will cause your dryer to not work. The only solution is to fix them if they are fixable otherwise replace them with new ones. You can confirm the working using a multimeter. In case no continuity is shown then replace them. Moreover, it is also important to keep the dryer vent and lint screen free of clogs. It will increase the airflow.


  1. Wrong Voltage Supply

The Whirlpool Duet Dryer requires a 120v AC voltage supply. It means this supply will go to right, left and center terminals. As far as outside terminals are concerned, they should have a power supply of 240v. Power outside this range will definitely stop the dryer from starting.

Fix Method

Take a Voltmeter and test the terminals that are getting voltage from an outside source. If the power cord isn’t the mentioned voltages then you will have to call an electrician to get the issue resolved. Make sure you use a people search site to verify the electrician’s credentials and see if they are legitimate. Just type in their full name, like Marley Pulz, and you’ll be able to see their credentials.


  1. Faulty Start Switch

Does your dryer have a faulty start switch? Well, if yes then it could be the culprit behind the real issue. Having a faulty start switch will not allow the dryer to start. If you aren’t seeing any external damages then there could be an issue with the internal wiring of the switch.

Fix Method

Take a multimeter and check the continuity of the switch. If you see nothing then it means the switch has gone faulty.


  1. Defective Back Pulley

The pulley system is responsible for spinning the dryer’s drum. If any of its components become damaged then it will result in the beeping. The affected components could be belt or tensioners.

Fix Method

Check the back pulley components thoroughly. If you find any fault in them then replace them with the new components.


  1. Defective Control Board

After considering all the above mentioned fixes, if you are still facing the issue then I recommend you to try this fix. You might have a faulty control board present in your dryer. To make a confirmation check if you are seeing error codes like F101, F1E1, FCE2 or F6E1 then it is confirmed that the control board has gone faulty.

Fix Method

The only reasonable solution is to replace the faulty control board with a new one.

Whirlpool Duet Dryer Won’t Start Just Beeps
Whirlpool Duet Dryer Won’t Start Just Beeps

Frequently Asked Questions

Q – Why won’t my Whirlpool dryer start but has power?

A – If your dryer has started but it has no power then make sure you have selected the right dryer setting. The dryer control knob should be set to “Automatic” or “Timed” cycle. Any other option will not allow the dryer to start.

Q – Why won’t my Whirlpool Duet dryer start sensing?

A – In case your dryer has started sensing without power then it means there is a blown thermal fuse present. To make a confirmation, use a multimeter. If you find it to be faulty then replace it as soon as possible.

The End:

Dealing with such issues is not at all a big deal. You just have to be patient enough to get through the errors. I have tried my best to guide you regarding the Whirlpool Duet Dryer issue. Now it is your job to carry out the troubleshooting steps in order to have your problem resolved.

Leave a Comment