If you were to rate the importance of a dishwasher in your kitchen, how much would you rate it out of 10? Well, a rough estimation would be 9/10 or 10/10. Most people like to rate a 10/10 because dishwashers actually hold great importance when it comes to washing dishes. Similarly, Frigidaire gallery dishwasher is one of the dishwashers that provide ease and comfort to the users.
But what if there comes a time when it stops working? Of course, the only possible solution left would be to reset it. The question is, do you really know how to perform Frigidaire Gallery Dishwasher reset? If not then I am here to guide you so stay tuned!
Important Points to Consider
Before moving on to anything else it is important to have these 2 points in your mind.
- If you reset your Frigidaire Dishwasher regularly then it can resolve many common issues like unresponsive controls and error codes. Solving these issues will ensure an optimal performance and increase the lifespan.
- Keep your dishwasher working by cleaning the filters regularly. But make sure to follow proper maintenance practices that will prevent you from future inconveniences. Consult your user manual to follow the instructions or contact an expert to get the job done.
Frigidaire Gallery Dishwasher Reset Method
In order to perform a problem-free reset on your Frigidaire Gallery Dishwasher, follow the below mentioned steps.
Also Check: Fisher Paykel Dishwasher Troubleshooting
Turn off the Power
The very first step to follow is to turn off the power supply that powers up the appliance. This will provide you protection against electrical hazards and will also allow the dishwasher to reset completely.
- Look at the back of the appliance and find the power cord.
- Once found, unplug the power cord from the outlet. Or you can also turn off the circuit breaker that is supplying power to the dishwasher.
- Wait for some time so that the residual power in the dishwasher’s system dissipates.
By following the above mentioned steps you are actually performing a hard reset on your dishwasher. Performing a hard reset will clear all the temporary glitches that might be the culprit behind the malfunctioning. After completing this step successfully, move to the next one.
Remove Dishwasher’s Bottom Rack
After you have successfully turned off the power to the dishwasher, the next step is to remove the bottom rack. Removing the bottom rack will give you access to different components that might need inspection or cleaning.
- Pull the bottom rack gently until it is fully extended.
- Pull the front of the rack out of the dishwasher by lifting it slightly.
- Keep the bottom rack in a safe place.
After removing the bottom rack you will now have access to interior components such as spray arm and filter. Once you have access to these interior components, you can clean them for good maintenance. It will contribute to a much longer lifespan. Once you have carried out this step successfully, move on to the next one.
Clean the Filters
The most common reason behind a malfunctioning dishwasher is the presence of dirty or clogged filters. There might be some food particles or debris trapped inside the filters which is causing the issue. To deal with this issue you need to clean the filters.
- Find the filter assembly which is likely to be present at the bottom centre of the dishwasher. You might see multiple parts including fine filter, coarse filter and a cylindrical filter.
- Lift the filter carefully out of its housing.
- Use a soft brush or a sponge to clean the filters. If you want to adopt the easy way then rinse the filter under running water.
- Carefully inspect the filters for visible damages, if found then you need to replace them as soon as possible.
- Once you have cleaned the filters properly, the next step is to reinsert them into the housing.
It is advised to clean the filters regularly or once a month. This cleaning will prevent clogs and will ensure that the dishwasher is operating smoothly. Now you can move on to the next step.
Reset the Dishwasher Control Panel
Resetting the control panel of your dishwasher will resolve many issues like unresponsive buttons as well as error codes. It will allow the dishwasher to clear temporary codes that might be affecting the dishwasher’s performance.
- Power off the dishwasher by unplugging its power cord or turning off the circuit breaker.
- Wait for the residual power to be discharged from the dishwasher’s system.
- Depending on your model, either press the Start/Cancel button or the High-Temp button for 5 seconds.
- Release the button as soon as you see lights on the control panel or hear a beeping sound.
- Give a few minutes to the dishwasher to complete the reset process.
Note that the reset procedure might be different for some Frigidaire Dishwasher models so it is a good practice to consult the user manual for specific instructions regarding the resetting process. Now it is time to move on to the final step.
Restart the Dishwasher and Test
After completing all the above mentioned steps successfully, it is now time to restart the appliance and test its working.
- Plug in the power cord of the dishwasher securely and properly.
- Turn on the circuit breaker if it is OFF.
- Select the wash cycle that you want to run but make sure to close the dishwasher door first.
- Press the Start button to start the wash cycle.
- Inspect the wash cycle carefully and make sure it completes the working without any interruptions or errors.
- After the cycle has been completed, check the washed dishes for cleanliness.
If there is no visible issue to be found then it means your dishwasher is working perfectly fine and there is nothing to worry about.
Also Check: How to Reset a Bosch Dishwasher
Frequently Asked Questions
Q – How do you do a hard reset on a dishwasher?
A – Resetting your dishwasher is an easy task, you need to first unplug the power cord, wait for some time so that the electrical charge clears out of the dishwasher and then power up the dishwasher again.
Q – What buttons do I push to reset my dishwasher?
A – Start/Cancel button present on the control panel is mostly used to perform a reset on your dishwasher.
The End
All in all, resetting your Frigidaire dishwasher is an effective and simple way to troubleshoot commonly faced issues. By following the step by step procedure mentioned above, you can easily overcome problems like operational glitches, error codes or unresponsive controls.
Jennifer is a seasoned writer and editor who plays a crucial role in our team. Growing up in an environment where appliance repairs were a common sight, she developed a genuine passion for DIY appliance troubleshooting.
Jennifer’s knowledge encompasses a variety of appliances, and she excels at demystifying complex issues. Whether it’s refrigerators, air conditioners, or microwaves, she’s dedicated to providing clear, actionable solutions.
Jennifer keeps a vigilant eye on emerging DIY trends, always eager to share innovative techniques with our readers. Her mission is to inspire individuals, especially women, to embrace appliance troubleshooting as an achievable skill.