What’s the best thing about Frigidaire Gallery Dishwashers? Well, it is their amazing sensors which tell you regarding the malfunctioning parts of the dishwasher. If you follow this guide till the end then I assure you that you will be able to fix any type of error which comes your way.
How to Clear Error Codes?
If you come across a situation where you find error codes popping on your dishwasher’s display then you can reset it to make the errors go away. Now your next question would be how to reset the dishwasher. For this purpose you need to follow the below mentioned steps.
Steps to Follow:
- Keep pressing the “Cancel” button for straight five minutes.
- The error should be gone by now. If it doesn’t then replace the malfunctioning part.
- Call a technician if the issue still persists.
Also Visit: Bosch Dishwasher No Lights on Control Panel [5 Reasons]
Also Visit: KitchenAid Dishwasher Diagnostic Mode [6 Ways to Run]
Also Visit: Maytag Bravos XL Washer Troubleshooting [10 Fixations]
Also Visit: Miele Dishwasher Troubleshooting [Top 5 Fixations] 2024
Also Visit: Why Bosch Dishwasher Starts Then Stops [4 Reasons 2024]
Frigidaire Gallery Dishwasher Error Codes
Following are some of the most commonly errors occurred on Frigidaire Gallery Dishwashers error codes.
PF
The error code PF occurs when a power failure occurs or when there is a 10% drop in the overall power.
Fix Method
Examine the voltage and make sure that it is supplying sufficient power to the dishwasher. If so then you need to reset the dishwasher using the method explained above. You can also turn it off for 5 minutes and then turn it back on.
HO
The error code HO occurs when the water takes too long to heat up or when the temperature is significantly low.
Fix Method
Always run the water before starting the dishwasher cycle so that the cold water residing in the lines flushes out. Check the water heating system thoroughly.
LO
The error code LO occurs when the rinse aid dispenser needs to be filled immediately.
Fix Method
You need to refill the rinse aid dispenser in order to resolve the issue.
CL
The error code CL occurs when the control board has detected that the dishwasher door has not been closed properly.
Fix Method
Make sure to close the door properly. If the issue still persists after this then you need to check the door switches. In case they are faulty, make a replacement for them. However, if the issue still exists then you need to make a replacement for the complete control board.
rA
The error code rA occurs when the rinse aid switch has gone defective.
Fix Method
First you need to refill the rinse aid dispenser. But if you see that the error still exists then check the wiring between the main control board and dispenser. If you still couldn’t find out the main problem then the best solution is to replace the whole control board.
RE and RF
The error codes RE and RF occur when the aid reed switch present in the dispenser is either open (RF) or close (RE).
Fix Method
Refill the dispenser to make the error code go away. If this proves to be unlucky for you then you need to replace the dispenser.
i10
The error code i10 occurs when a water supply issue occurs indicating the low water level.
Fix Method
Examine the water supply line carefully. It shouldn’t be blocked or kinked in any way. Also check the water controller knob is in ON position.
i20, i40, iF0
When these error codes occur it means that either the filters have been clogged or the drain line has been restricted.
Fix Method
Thoroughly check the drain hose for possible kinks and blockages. Clean all the areas along with filters carefully. In addition to this, check whether the knockout plug has been removed or not.
i30
The error code i30 occurs when there is a water leakage in the dishwasher base.
Fix Method
You need to check the pressure sensor, water inlet valve and drain pump for debris or clogging. If any of these is clogged then you need to do some cleaning as soon as possible. However, in case of severe defect, make a quick replacement.
i60
The error code i60 occurs when there is any problem with the water heating system.
Fix Method
Keep holding the Cancel button to reset your dishwasher. If the issue still persists then you need to call a technician and have your water heating system checked.
iC0
The error code iC0 occurs when there has been a fault with the electronic control system.
Fix Method
Same fix method goes for this error code as well. Either reset the dishwasher by pressing the Cancel button for 5 minutes or call a professional to get the job done.
UO
The error code UO occurs when the main control board fails to receive signals from the vent assembly about the vent plunger being closed. It indicates that the vent is still open.
Fix Method
Check the wiring between the control board and vent assembly. If this is not the issue then you need to replace the vent assembly or the main control board to fix the issue.
ER
The error code ER occurs when any key has been pressed for too long or it has been stuck.
Fix Method
First check the keys present on the control panel, they shouldn’t be pressed or stuck. Moreover, check the wiring present between the keypad and the control board. In case you are unable to identify the issue, you need to replace the keypad. But if the issue still exists then replace the main control board.
CE
The error code CE occurs when there is a configuration error.
Fix Method
Examine the wiring connections between the main control board and keypad. If any parts demand a replacement then do it as soon as possible.
tu
The error code tu occurs when there has been a failure in the turbidity sensor.
Fix Method
Check the wiring between the control board and turbidity sensor. If you cannot find any issue then replace the sensor.
UF
The error code UF occurs when the control board is sensing that the fan motor of the vent is not operating at the correct speed.
Fix Method
First check the wiring and if you cannot find anything weird then replace the vent fan immediately. If you still get unlucky then replace the whole control board.
hs
The error code hs occurs when there is a hall sensor issue related to the motor.
Fix Method
Check the wiring, if this is not the issue then replace the motor and if this isn’t the issue as well then replace the whole control board.
i50
The error code i50 occurs when there is a fault with the wash motor or drain.
Fix Method
Reset the dishwasher using the same approach. If the error returns again then troubleshoot the drain or call an expert to get the job done.
dP
The error code dP occurs when the drain pump has been activated during the relay test.
FL
The error code FL occurs when the water valve has been activated during the same relay test.
rt
The error code rt occurs when the relay/triac test has been started.
Sd
The error code Sd occurs when the detergent dispenser has been activated during the test.
UL
The error code UL occurs when the UL test has been activated.
Also Visit: Bosch Dishwasher Cycles Explained [Complete Guide 2024]
Also Visit: Why Is My KitchenAid Dishwasher Beeping [9 Issues & Fixes]
Also Visit: GE Dishwasher Troubleshooting [7 Fixations of Problem] 2024
Also Visit: Bosch Dishwasher cant Change Cycle [5 Things To Do]
Also Visit: Kitchenaid Dishwasher Not Spraying Water 2024
Frequently Asked Questions
Q – How do I clear the error codes on my Frigidaire Gallery Dishwasher?
A – You simply have to reset your dishwasher in order for the error codes to go away. Keep pressing the Cancel button for 5 minutes and you will have the dishwasher reset.
Q – What is the code 4 on a Frigidaire dishwasher?
A – The error code 4 on a Frigidaire dishwasher indicates the presence of faulty temperature sensors.
The End
All in all, there are a total of 23 error codes associated with the Frigidaire Gallery Dishwasher. If you want to get rid of them then you need to follow the above guide in order to solve them. However, if you are unable to do so then you are encouraged to contact professionals.
Jennifer is a seasoned writer and editor who plays a crucial role in our team. Growing up in an environment where appliance repairs were a common sight, she developed a genuine passion for DIY appliance troubleshooting.
Jennifer’s knowledge encompasses a variety of appliances, and she excels at demystifying complex issues. Whether it’s refrigerators, air conditioners, or microwaves, she’s dedicated to providing clear, actionable solutions.
Jennifer keeps a vigilant eye on emerging DIY trends, always eager to share innovative techniques with our readers. Her mission is to inspire individuals, especially women, to embrace appliance troubleshooting as an achievable skill.