Maytag Bravos XL Washer Troubleshooting [10 Fixations]

When you hear about Maytag Bravos then there should be nothing left behind to make a doubt. It is one of the leading brands which doesn’t compromise on the quality no matter what. However, there always come problems along with various electrical appliances. Today, I will be guiding you about Maytag Bravos XL washer troubleshooting methods. Stay tuned with me!

Maytag Bravos XL Washer – Common Problems:

Before jumping on to the fixes, it is a good practice to first know about the common problems faced by this washer.

• Lid lock issues
•       Unbalanced load
•       Error codes
•       Not draining properly
•       Washer not filled with water
•       Excessive noise and vibration
•       Washer not spinning
•       Detergent dispenser issues
•       Leaking water
•       Washer stops mid-cycle

Maytag Bravos XL washer troubleshooting methods

After having adequate knowledge regarding the common problems, now is the time to discuss its fixes. I will be discussing every problem briefly and will then guide you about its fix.

1. Lid lock issues

This is the most common issue faced by the users of Maytag washer. Consider this as a safety feature because it will not allow the machine to operate until and unless the lid is closed properly. The normal functioning of the washer will be greatly affected if the lid lock starts malfunctioning.

Fix method

If you have made a confirmation about the presence of a faulty lid lock then it is better to fix it as soon as possible. Moreover, you can even contact an expert and get your faulty lid lock replaced by a new one.

Also Visit: Why Is My KitchenAid Dishwasher Beeping [9 Issues & Fixes]

Also Visit: GE Dishwasher Troubleshooting [7 Fixations of Problem] 2024

Also Visit: Whirlpool Dishwasher Diagnostic Mode [4 Methods]

Also Visit: Bosch Dishwasher cant Change Cycle [5 Things To Do]

Also Visit: Kitchenaid Dishwasher Not Spraying Water 2024

Also Visit: How to Reset a Bosch Dishwasher [Steps For Fixation 2024]

2. Unbalanced load

Having an unbalanced load in the washer drum will create many problems for you. If this happens then the washer will vibrate excessively and produce loud noises. Moreover, it can also stop mid-cycle. However, this issue is not specifically related to Maytag washers as it can happen to any washer.

Fix method

You can redistribute the laundry and fill the drum according to its capacity. Along with this, check the water-levelling and also sort your clothes by weight.

3. Error codes:

The best thing which Maytag washers have to offer to their users is the information about improper functioning of the washer. This information is circulated through error codes being displayed on the washer’s display panel.

Error codes can be considered as diagnostic tool because they allow the user to gather knowledge about the problem and then troubleshoot it.

Fix Method:

Every code points towards a specific problem. You first need to see what the error code is about and then use your user manual for further details. Most of the error codes are about draining, temperature sensor and internal components. So you must have basic-knowledge regarding this.

4. Not Draining Properly

Draining not being performed properly might lead to many issues. Suppose you run a spin cycle but due to poor drainage, your clothes are left wet. Wouldn’t it be frustrating for you? Of course, it would! You cannot pinpoint one issue and label it as the problem. Many factors contribute to this problem.

Fix method

The possible solution of this problem is to clean the drain pump filters and examine the drain hose properly.

5. Washer Not Filled With Water:

If the washer stops filling up with water then it can greatly affect the cleaning of your clothes. They can remain dirty even after a complete wash-cycle.

Fix Method:

Make sure the valves for both hot and cold water should be turned ON. They need to be fully open for a proper water flow.

Examine the hoses which connect the water supply to the washer carefully. Remove all the possible blockages and kinks from the hose. If the hose has been damaged then you need to replace it as soon as possible. Moreover, if it is clogged then use a brush to unclog it.

Inspect the water inlet valve carefully. If the valve is malfunctioning or damaged then you need to make a replacement.

6. Excessive Noise and Vibration:

Hearing excessive noise and vibration from your washer can be really annoying. You need to resolve this issue before it becomes a real problem for you. The potential reasons for this problem are:

• Unbalanced load
• Faulty suspension rods
• Defective tub bearing

Fix method

To resolve the unbalanced load issue, you need to redistribute the laundry evenly. Moreover, sort the clothes by weight.

Due to continuous working, the suspension rods can wear out. It disturbs the stabilization of the washer tub and causes the tub to shake and make excessive noises. Replace these rods to continue the proper working of your washer.

Tub bearing helps the washer’s drum to spin smoothly. If due to any reason, the bearing has become faulty then it will make the drum to produce unusual sounds. Make a replacement for your defective tub bearing.

7. Washer not spinning

Washer not spinning could be a real problem for you. Firstly, it will not clean your clothes properly. Secondly, it will leave your clothes wet. Following factors contribute to this cause.

• Damaged drive belt
• Malfunctioning motor
• Faulty lid switch

Fix Method:

The drive belt is responsible for spinning. It connects the motor to the washer’s drum. But due to continuous work load, the belt can become faulty and the only possible solution left for this would be a replacement.

The motor’s engine not operating properly will require you to contact a technician and get the job done.

Lid switch ensures the proper working of the washer. The washer will work if the lid is closed, if this is not the case then the washer will refuse to rotate. Test the lid switch for continuity and if results are not up to the mark then get it replaced.

8. Detergent Dispenser Issues:

If your washer is facing dispenser issues then it can affect the cleanliness of your clothes. The clothes will not be cleaned properly and efficiently. Following are the reasons for this.

• Clogged dispenser
• Drawer that won’t open
• Faulty dispenser motor

Fix method:

Consult the user manual and remove the drawer by following the instructions present in it. Clean the drawer along with its compartments thoroughly.

Check the drawer for possible damages and if found then you can replace the faulty drawer with a new one.

Dispenser motor also plays an important part. If the drawer itself is in good condition then the real cause of worrying could be the dispenser motor. Contact a technician, have the motor checked thoroughly and get it replaced or fixed as per the requirements.

9. Leaking Water

Water leakage is a real problem to deal with. It can become a danger for your home and washer as well. However, the water leakage problem can occur at different phases of the washing. Potential causes for this problem are:

• Damaged door seal
• A loose hose
• Faulty water pump

Fix method

Inspect the gasket carefully and check for possible damages. If any damage is found then you need to replace it. Moreover, have the seal cleaned and free of any unwanted material.

There is no other solution than to replace the damaged hoses. Along with this, tighten any loose connections found.

If the above two things are in a clear zone then you need to check the water pump for possible leakages. Replace it or fix it by a technician.

10. Washer Stops Mid Cycle:

Having your clothes half soaked in water and detergent might be really frustrating for you, isn’t it? Well, it could happen if the washer stops mid-cycle. There are many potential reasons for this such as:

• Overloaded washer
• Overheating motor
• Faulty door lock

Fix Method:

There is a mechanism present in the washer which allows it to shut down in order to protect itself. If the drum is filled with more than its capacity then the washer will not work. You need to fill the drum according to the capacity of your washer.

Due to some reason, if the motor gets overheated then the washer will stop working mid-cycle. The working will be resumed once the motor cools down.

As discussed before, the washer will not operate until and unless it has surety regarding the lid lock. If it is faulty then you need to make a quick replacement.

Also Visit: Bosch Dishwasher No Lights on Control Panel [5 Reasons]

Also Visit: KitchenAid Dishwasher Diagnostic Mode [6 Ways to Run]

Also Visit: Miele Dishwasher Troubleshooting [Top 5 Fixations] 2024

Also Visit: Why Bosch Dishwasher Starts Then Stops [4 Reasons 2024]

Also Visit: Bosch Dishwasher Cycles Explained [Complete Guide 2024]

Frequently Asked Questions

Why is my Maytag washer not starting?

The Maytag washer not starting could be due to the following reasons.

• Washer overheating
• Blown fuse

You need to inspect the fuse for continuity using a multimeter. If you witness any continuity then it means the working is fine.

Does a Maytag Bravos XL have a reset button?

Yes, Maytag Bravos XL has a reset button. It is normally located near a control panel or inside the main compartment of the washer.

Ending words

All in all, every appliance has some issues which the user will have to face sooner or later. I have guided you through possible problems along with their fixes. Now the next step would be to figure out the problem of your washer and apply a relevant fix against it.