Whirlpool Duet Washer Reset [Fixation 2024]

Are you a regular customer of the Whirlpool brand? Well, it is a nice thing because Whirlpool products have taken over the market by storm. Millions of people all over the world use this brand. But buying these products is just not enough, you need to be familiar with its troubleshooting methods as well.

For starters, let us consider the reset method of Whirlpool Duet Washer. Did you ever come across the need to perform a reset on your Whirlpool Duet but didn’t know how to? Don’t worry, I will be guiding you regarding this here!

In Which Situations Does a Whirlpool Duet Washer Demand a Reset?

Make sure not to perform a reset every time you come across some issue. There are some situations which actually demand a Whirlpool Duet Washer Reset. I will be explaining them below so make sure to go through them carefully.

1. 
   

   Error Codes

Error codes are handy when the washer wants to tell you that there is something wrong with it. If you reset your washer then the error code might disappear. But if the error code still persists even after the reset then you most probably need to replace the defective component.

2. 
   

   Installation of New Parts

Installing a new part in your washer means that some time will be required by your washer in order to recognize it and work efficiently with it. Resetting a washer in this situation is highly encouraged as it allows the machine to recalibrate its functions to work with the newly installed component.

3. 
   

   Load Imbalance

Overloading your washer with laundry might damage the appliance and cause potential leaks. There are many sensors present which detect this imbalance, as a result the washer will lock itself and refuse to move. Resetting your washer in such a situation might help you.

4. 
   

   Power Issue

Have you recently experienced a power surge? If yes then the washer’s electronics might malfunction and you need to reset it. After resetting, it is ensured that all the electronic issues are cleared.

How to do Whirlpool Duet Washer Reset?

Now the question comes, how to perform a reset on your Whirlpool Duet Washer. There are 6 ways to do it. Let me explain all of them one by one.

Also Check: Correct Washing Machine Drain Pipe Height

Unplug the Washer

• Turn OFF your washer by pressing the Power or Cancel button.
• Unplug the washing machine from the power outlet carefully.
• Leave the washer in the same condition for about 5 minutes,
• Now re-establish the connection and reconnect your machine to the outlet.
• Turn ON your washer by pressing the Power or Start button.

Turn Off the Circuit Breaker

• The first step is to locate your circuit breaker corresponding to the laundry room.
• Once found, flip the breaker to the OFF position.
• Leave it like this for 5 minutes.
• Now flip the breaker to ON position.
• Turn ON your washer by pressing the Power or Start button.

Press and Hold Buttons – Start and Power

• Press and keep holding the Start or Pause button at the same time.
• Keep holding them for 5 seconds.
• Now release the buttons and run a cycle to check whether the washer has been reset or not.

Using Dial Method

Some of you might own a washer having a dial instead of a touch panel. But don’t worry as you can still perform a reset.

• Make sure that the control panel is OFF.
• Now rotate the dial like you used to do it when setting a normal wash cycle.
• You need to turn the dial a full rotation in a counter clockwise direction.
• After the dial has come to its initial position, turn the dial only one click to the right. For the last time, turn it one more click to the left.
• Once the sequence is completed, wait for a minute.
• In case the washer has been reset successfully, all the lights present on the machine should turn ON and OFF again.
• Perform a test cycle and see whether it is completed without any issues or not.

Open and Close the Washer Lid

• The washer should be ON but it shouldn’t be running.
• First open the washer’s lid fully and then close it firmly.
• Repeat the above step 6 times within a time span of 12 seconds.
• After this has been done, set the washer for a short cycle for testing purposes.
• Make sure the cycle is completed without any issue.

Recalibrate the Washer

• Unplug the washer and wait for about 1-2 minutes.
• Enter the diagnostic mode of your washer by rotating the dial clockwise three clicks, then rotating it counterclockwise one click and finally rotating it clockwise one click.
• If you have followed the sequence correctly then the lights on the washer should turn ON indicating that you have entered the diagnostic mode successfully.
• Now enter the calibration mode by turning the dial clockwise for 4 clicks until you see “Rinse” light being illuminated.
• Press Start button to begin with the calibration process.
• The washer will go through a series of tests including filling with water, spinning, draining and agitating.
• After this has been completed, the washer should exit the diagnostic mode automatically.

Also Check: Reason GE Washer Stuck on Sensing

Frequently Asked Questions

How do I clear the error code on my Whirlpool Duet?

In order to remove the error code on your Whirlpool Duet, press the pause or cancel button twice while the power button only for once.

How do I reset my Whirlpool Panel?

A – To reset the Whirlpool panel you simply have to unplug your washer from the outlet. Wait for about a minute and then plug it back. In case your washer is hard-wired then you need to deal with the breaker and turn it to ON and OFF position for one minute.

The End:

All in all, Whirlpool washers do experience minor glitches and issues which affect their performance. No matter what the issue is, a simple reset can save you from a lot of future trouble. But even after resetting, if your washer is still experiencing the same issue then you need to look out for some technical help. You are highly encouraged to deal with the issue on your own first.